Lighting Control

The DMX splitter allows connection of DMX receivers (dimmers, color changers, moving lights, etc.) in a star configuration as opposed to a daisy chain configuration. In a star configuration, each control cable is run to a central point, in ...

For the receiving end of long control runs the DMX512 Isolation Amplifier is recommended. It contains separate input and output power supplies. This allows the input circuitry to receive signals as low as 0.2 volts. These are optionally av ...

The Enhanced² Isolated Splitter [125EE-FT] includes all the features of DFD's standard models with added protection to meet the needs of harsh operating conditions. As with their standard splitters, all outputs are isolated from the i ...

This series of selector switches was specifically designed to switch DMX512 signals. Originally designed to switch between primary and backup consoles, these switches are often used to select from two (or more) input locations. The SW1 swi ...

This series of selector switches was specifically designed to switch DMX512 signals. Originally designed to switch between primary and backup consoles, these switches are often used to select from two (or more) input locations. The SW1 swi ...

Want to pile-on two DMX512 sources? You can't just tie the outputs together like you can with 0 to 10 volt analog control signals. Combining two DMX512 sources requires a computer, like the one in DFD's model 321E DMX Combine Unit. The com ...

The Rotor-Router is a DMX512 distribution system featuring up to 12 inputs and an unlimited number of outputs. A system typically consists of an input module and one or more output modules. Both modules are 1.7"h x 19"w x 12"d and are norm ...

The Rotor-Router is a DMX512 distribution system featuring up to 12 inputs and an unlimited number of outputs. A system typically consists of an input module and one or more output modules. Both modules are 1.7"h x 19"w x 12"d and are norm ...

The analog to DMX512 converter accepts 48 discrete analog control voltages and generates a DMX512 control signal based on these inputs. The most common configuration converts each analog signal to one DMX512 output level with the first ana ...

DMX512 control of low voltage switch closure devices (such as slide projectors and fog machines) is made possible with these low voltage DMX Relay Packs. Doug Fleenor Design relay packs use dry contact air-gap relays. These relays have adv ...

The DMX96OC is designed to drive solenoids and relays for fountains or special effects, and is ideal for many other on/off loads. The product decodes 96 consecutive DMX512 channels to drive open-collector NPN outputs. Each of the outputs i ...

The DMX2DALI interface has an opto-isolated DMX512 input and two DALI output ports. Each output port is capable of individually addressing 64 DALI devices. There are modes to allow for single channel control of all ballasts (broadcast mode ...

The DMX512 iPlayer interface receives a DMX512 input signal and outputs RS-232 commands to the iPlayer. The interface uses three consecutive DMX512 channels: trigger mode, show selection, and global intensity. The interface is compatible w ...

The DMX2DMX addresses issues associated with non-compliant DMX devices. Many lighting devices claim to accept DMX512 signals, but are unable to support the wide variety of timing parameters allowed by the DMX512 standard. The result is fli ...

The DMX512 DIN-rail mounted interfaces are interface products that receives DMX512 lighting control protocol and generate various signals to interface with other show control elements. The interface is currently available with three common ...

The Doug Fleenor Designs Rerun Rack Mount is a multi-universe lighting controller capable of storing up to ten 40-minute shows. Shows are recorded by capturing the output of a DMX512 console. The recorded show start and end points may be t ...

The Doug Fleenor Designs RERUN-R3 Rerun Rack Mount is a multi-universe lighting controller capable of storing up to ten 40-minute shows. Shows are recorded by capturing the output of a DMX512 console. The recorded show start and end points ...

The Doug Fleenor Designs RERUN-R4 Rerun Rack Mount is a multi-universe lighting controller capable of storing up to ten 40-minute shows. Shows are recorded by capturing the output of a DMX512 console. The recorded show start and end points ...

The Doug Fleenor Designs Color Wheel is a simple wall-mounted device designed to operate DMX512 based LED lighting fixtures. It can be configured to operate 3, 4, or 5 channel fixtures. Active channels may be increased or decreased individ ...

The Rerun Portable is a lighting control station capable of storing up to ten 40-minute shows. Shows are recorded by capturing the output of a DMX512 console. The recorded show start and end points may be trimmed non-destructively. Each sh ...

The DMX24DIM is a twenty-four output dimmer designed for high efficacy loads, low idle power, and minimal losses. Typical loads include Christmas light strings (LED and incandescent), and low power lamps such as LED, neon, compact fluoresc ...

This is a power supply that is designed for use with the DFDNET Distribution Isolator.

The Enhanced2 Isolated Splitter [125EE] includes all the features of DFD's standard models with added protection to meet the needs of harsh operating conditions. As with their standard splitters, all outputs are isolated from the input and ...

The City Theatrical 3665 Moving Light Assistant is an application designed to document both the physical setup and programming information for moving light rigs commonly used in the entertainment industry. The application will run on both ...