Product Overview
Bogen's Wall-Mount Power Vector modular amplifiers offer a wide range of power from which to choose from, with three models ranging from 100W to 250W. The amplifiers are designed to work with both high- (70/25V) and low- (4/8-ohm) impedance speaker systems.
Each model includes eight module bays for plug-in input modules and allows for up to four levels of priority between modules. Two module bays are capable of accepting signal processing plug-in output modules. Each module is controlled by an independent volume control with an associated signal/clip LED for signal status. An 11-segment LED output meter monitors output signal level.
Each model includes a motorized master volume control that can be controlled using a remote volume control panel (RVCP, sold separately).
Bogen Communications WV250 Features:
- 100-, 150-, and 250-watt models, each with a large power reserve
- Capable of handling 70V, 25V, 8-ohm, and 4-ohm speaker loads
- 8 module bays
- Wide selection of advanced plug-in modules
- 2 module bays capable of handling signal processing plug-in output modules
- 4 levels of priority between modules
- 11-segment LED output level meter monitors the output level of the power amplifier with Peak and Average meter switch
- Adjustable output level limiter with limit indicator
- Tape output available on front of unit
- Optional front-mounted input combo jack with 1/4" stereo phone and female XLR capabilities
- Motorized master volume control can be remotely operated
- Bass and treble controls with center detent
- Two-color LED for each channel indicates input active/clipping
- Switch permits user to select either transformer-coupled or a direct low-impedance output
- Bass and treble control bypass switch (located in module bay 6)
- 125 Hz Lo-cut feature (switch located in module bay 6)
- 5-position barrier strip, with clamping washers, provides connections for speaker loads
- Master mute function overrides all audio from the mixer section of the amplifier
- Screw terminal for master mute and remote volume control functions
- Each of the 8 module bays has an associated independent volume control
- Remote volume control panel (RVCP) (sold separately)
- Requires flush-mount (Model BBF) or surface-mount(Model BBS) back boxes (sold separately)
- Requires front cover door (WMAD sold separately)
- UL and CSA listed
Bogen Communications WV250 Specifications:
- Power Output (RMS): 250W (340W typical, @ 1kHz/0.1%/4 ohms)
- Frequency Response:
- Transformer: 45Hz-20kHz; 0/-2dB @ FRP
- Direct: 20Hz-20kHz; 0/-1dB @ FRP
- Distortion:
- Transformer: 0.5% THD+N, Maximum, Full-rated bandwidth @ FRP
- Direct: 0.1% THD+N, Maximum, Full-rated bandwidth @ FRP
- Signal-to-Noise:
- Fundamental: -94dB
- With Aux Module: -70dB
- With Mic Module: -60dB
- With Tel Module: -70dB
- Tone Controls:
- Bass Frequency: 100Hz (+/-10dB minimum)
- Treble Frequency: 10kHz (+/-10dB minimum)
- Low Cut Frequency: 125Hz @ -6dB/octave
- Sensitivity: 0.4V (at backplane connector)
- Output Regulation: 2dB or better no load to full load
- Output Impedance:
- Transformer-Coupled: 70V, 25V, 8 ohms; balanced or unbalanced
- Direct Coupled: 4 ohms unbalanced
- Tape Out:
- Output Level: 4VRMS @ FRP
- Output Impedance: 50 ohms maximum
- Overload Protection: Electronic overload protection (auto reset)
- Thermal Protection: Thermistor attached to heat sink
- Line Fusing: Resettable circuit breaker
- Cooling: Thermally controlled 3-speed fan
- Power Consumption: 5.5A @ 120V AC, 60 Hz
- Dimensions: (W x H): 14 1/8" x 21"
- Weight: 28 lbs
