Product Overview
The CONVERGE® Pro 2 120 is an advanced multi-channel microphone auto mixer with the latest audio DSP algorithms, from ClearOne. This mixer adds Twelve (12) configurable mic/line audio inputs and built-in USB audio in an installation, and adds a powerful Digital Signal Processor.
Image shown above is for illustrative purposes only; actual product appearance may vary.
ClearOne 910-3200-004 Includes:
- (1) 6’ Grounded Power Cord
- (12) Orange 3 Position Terminal Block Input Connectors
- (1) Green 6 Position Terminal Block GPIO Connector
- (1) 18” RJ-45 To RJ-45 C-Link Cable
- (1) 6’ USB Type A to Type B Cable
- (2) Pre-installed Rack Ears
- Rack Decor Screw/Washer Kit
ClearOne 910-3200-004 Features:
- 12 mic/line inputs
- USB audio
- C-Link and P-Link enable addition of DSPs and peripherals
- Flexible control options include Touch Panel Controller, BYOD dialer apps or 3rd party control modules
- Configure an entire system of C-linked DSPs with CONSOLE AI software
- Built-in DARE™ algorithm for dynamic feedback elimination
- Connect via C-link to VoIP and Telco enabled DSPs for conferencing
- Reduced foot-print and power consumption
ClearOne 910-3200-004 Specifications:
- MIC/LINE INPUTS
- Inputs:
- Balanced audio inputs
- 3.81mm Orange color Phoenix/Euroblock type male header
- Push-on mini-terminal block
- Frequency Response: 20Hz – 22kHz @ +4dBu, +/- 0.5dBu
- EIN (Equivalent Input Noise): 20kHz BW, max gain, Rs = 150Ω, -126dBu
- THD + N (Total Harmonic Distortion + Noise):
- 20Hz – 22kHz @ +4dBu, line level, 0.006%
- 20Hz – 22kHz @ -56dBu, mic level, < 0.04%
- Dynamic Range: 20Hz – 20kHz @ 0dB, > 105dB
- Crosstalk (Mic/Line): Channel to Channel, stimulus at 20dBu to receptor at -56dBu, 1kHz, < -98dB
- Input Impedance: Balanced (line to ground), 2.2kΩ, 1%
- Maximum Input Level: -65dBu to 20dBu
- Phantom Power: 48V, Impedance 6.81kΩ
- USB AUDIO
- Port Type: USB-B connector
- Audio: Digital Audio, 2 x 2 bidirectional channels
- Compatible:
- Sample Rate: 48kHz
- Sample Bit Depth: 24-Bit
- ETHERNET
- Port Type: RJ-45, 10/100Mbps Ethernet Network, Auto Negotiation
- IP address: IPv4 (IPv6 upgradeable through future s/w, f/w upgrade)
- C-LINK EXPANSION BUS
- Ports Type: RJ-45 (Cat5e or Cat6)
- C-Link In & Out: Proprietary Expansion Bus
- Audio: 64 Expansion channels
- Cable: Solid core, factory terminated Cat 5e or 6 cable
- Distance: Up to 150’ (45M)
- P-LINK PERIPHERAL BUS
- Ports Type: RJ-45 (Cat5e or Cat6)
- P-Link In & Out: Proprietary Peripheral Bus
- PoE In:
- P-Link In Port
- PoE 802.3af Mode B, Midspan
- Power on “spare pairs” 4,5 and 7,8
- Input voltage range: 48V to 56V
- Audio: Up to 3 Beamforming Microphone Array 2 units + up to 3 DIALOG 20 Wireless Receiver units + Up to 3 USB Expander units + Up to 3 GPIO Expander units
- Cable: Solid core, factory terminated Cat 5e or 6 cable
- Distance: Up to 200’ (60M)
- Long Distance P-Link:
- Increases P-Link distance from 200 Ft to 650 Ft
- 650 Ft (200M) maximum cable distance between any two units
- Cat6, 550 MHz, 23 AWG, solid conductor cable
- Do not use Copper Clad Aluminum (CCA) cable
- Available only for BFM2 peripheral units
- 48V PoE Midspan Mode B power injector for 1 BFM2 unit
- 56V PoE Midspan Mode B power injector for 3 BFM2 units
- RS232
- Port Type: DB9 Female
- Settings: 9600/19200/38400/57600/115200 Baud; Serial Echo; Flow Control
- Support: Serial commands
- GPIO
- Port Type: 5.08mm Green color Phoenix/Euroblock type male header
- Support: Control, Status, Variable Voltage Control
- Power Pin: 5V DC @ 350mA Power Source
- Pin 1 to 4:
- Open Collector Outputs: 40VDC @ 250mA
- Active Outputs (Source/Sink): 5VDC @25mA
- Logic Inputs: 40.2kΩ pull up
- Variable Voltage Control Inputs: 5VDC max
- Ground Pin: GND
- USB CONTROL
- Port Type: USB-B connector
- Compatible:
- Location: Front Panel
- LEDs
- Location: Front Panel
- Status LED:
- Off: Unit still initializing
- Blue - Fast Blinking: Stack Syncing in progress
- Blue - Slow Blinking: Unit not configured
- Blue - Solid: Configured unit
- Red - Fast Blinking: Stack Sync error
- Locate LED: Blue - Blinking: Unit “Locate” command received
- Power LED: Blue - Solid: Unit is powered on
- TOUCH SENSOR
- Sensor Type: Capacitive Touch Button
- Location: Front Panel
- POWER & THERMAL
- Port Type: AC Inlet
- Mains Voltage: 100-240V AC, 50/60Hz
- Power Consumption: 50 Watts Typical
- Thermal: 170 BTU/Hr Typical
- Ambient Operating Temperature: 14°F to 104°F (-10°C to 40°C)
- DIMENSION & WEIGHT
- RU size: 1 RU
- Dimensions (WxDxH):
- Without rack-ears: 17” x 10.73” x 1.72” (43.2 x 27.3 x 4.4 cm)
- With rack-ears: 19” x 10.73” x 1.72” (48.3 x 27.3 x 4.4 cm)
- Unit Weight (Approx.): 9.3 lbs (4.2 kg)
- Shipping Weight (Approx.): 13.8 lbs (6.3 kg)