Studio Technologies MODEL-5412-01 Audio Interface, with Dante 8x8

Studio Technologies MODEL-5412-01 Audio Interface with Dante 8x8

The MODEL-5412-01 provides a high-performance, easy to use, 8 input/8 output interface for line-level analog signals with applications that use Dante® audio-over-Ethernet media networking technology. Line level analog audio input signals are converted to PCM digital then transported via a Dante interface. Using the Dante Controller software application, digital audio signals can be routed to the Model 5412 via the Dante interface. The Model 5412 is an ideal compact and cost-effective “edge” device for Dante network implementations, providing line level input and output resources, and can also serve as a general-purpose audio tool to help extend Dante capabilities to applications and facilities initially implemented to support analog signals.

Studio Technologies MODEL-5412-01 Includes:

• MODEL-5412-01 Audio Interface with Dante 8x8

Studio Technologies MODEL-5412-01 Features:

• 8 input, 8 output line-level analog audio to Dante interface
• Excellent audio quality
• Analog line-level inputs to Dante outputs
• Dante inputs to analog line-level outputs
• Special analog mixer function for matrix intercom applications
• Three Gigabit Ethernet interfaces
• Standard connectors
• AC mains and 12-volt DC powering
• Lightweight enclosure with single rack-space (1U) mounting

Studio Technologies MODEL-5412-01 Specifications:

• Network Audio Technology:
  • Type: Dante audio-over-Ethernet
  • AES67-2018 Support: Yes, selectable on/off
  • Ethernet Interface Configuration: Switched or redundant
  • Dante Domain Manager™ (DDM) Support: Yes
  • Sample Rates: 44.1, 48, 88.2, and 96 kHz
  • Bit Depth: Up to 24
  • Dante Audio Flows: 32 transmitter, 32 receiver
  • Dante Transmitter (output) Channels: 8
  • Dante Receiver (input) Channels: 8
• Network Interfaces:
  • Qty: 3, Dante Primary, Dante Secondary, and Management
  • Type: 1000BASE-T Gigabit Ethernet (GigE) per IEEE 802.3ab (100Mb/s also supported but not recommended for optimal performance- 10Mb/s not supported)
  • Ethernet Connection NIC Status LEDs: One link and one activity for each Ethernet interface
  • Remote Configuration Capability: Uses webpages provided by internal webserver
  • Analog Inputs:
  • Type: Electronically balanced, capacitor coupled, intended for connection to balanced or unbalanced signal sources
  • Impedance: 20k-ohms
  • Nominal Level: +4dBu, reference -20dBFS, adjustable ±20dB in 0.1dB steps
  • Maximum Level: +24dBu, results in digital output level of 0dBFS
  • Dynamic Range: 120dB, A-weighted
  • Distortion (THD+N):
  • Frequency Response: ±0.2dB, 14Hz to 20kHz
• Analog Outputs:
  • Type: Electronically balanced, capacitor coupled, intended to drive balanced or unbalanced loads of 2k-ohms or greater
  • Source Impedance: 200 ohms
  • Nominal Level: +4dBu, reference -20dBFS, adjustable ±20dB in 0.1dB steps
  • Maximum Level: +24dBu
  • Dynamic Range: >119dB, A-weighted
• Distortion (THD+N):
  • Frequency Response: ±0.1dB, 6Hz to 20kHz
• 1kHz Tone Output:
  • Analog: 1kHz sine wave at +4dBu, nominal, adjustable ±20dB in 0.1dB steps
  • Dante (Digital): sine wave at -20dBFS, fixed
  • Front Panel Display: Backlit LCD
• Power Sources:
  • AC Mains: 100-240VAC, 50/60Hz, 20W maximum
  • DC: 1-018VDC, 1.5A maximum
• Connectors:
  • Ethernet: 3x RJ45 jacks
  • Analog Inputs & Outputs: 25-pin female D-subminiature (DB-25F), AES59-2012-compliant
  • USB: Type-A receptacle (used only for firmware updates)
  • AC Mains Input: 3-blade, IEC 320 C14-compatible
  • DC Input: 4-pin male XLR (pin 1 negative, pin 4 positive)
• Mounting: One rack space (1U)
• Dimensions: 19” wide x 1.72” high x 7.8” deep (48.3 x 4.4 x 19.8 cm)
• Weight: 3.2 lbs. (1.5kg)
• Environmental:
  • Operating Temperature: 0 to 50 degrees C (32 to 122 degrees F)
  • Storage Temperature: -40 to 70 degrees C (-40 to 158 degrees F)
  • Humidity: 5 to 95%, non-condensing