Product Overview
The Edge Digital Signal Processor stands out for its adaptability. Equipped with four card slots and an extensive selection of cards that users can install themselves, Edge becomes the preferred DSP for scenarios requiring a highly specific mix of functionalities where no other solution suffices.
Symetrix 80-0204 Features:
- Full-featured open-architecture DSP engine
- 4 mic/line inputs
- 4 line outputs
- Ultra-low noise Symetrix preamps with 3 dB gain steps
- 1× I/O expansion card slots
- 4×4 GPIO
- RS232 control terminal blocks
- ARC Remote port
- Optional 64×64 redundant Dante
- Optional 8 or 16 channel AEC coprocessor module
- USB audio port enables computer-based soft-codec conferencing
- or 8 channels of multitrack recording and playback
- USB host port supports 8 channels of audio recording and playback
- Dedicated routing and processing resources
- for a 128×128 Super Matrix
- Dual Dante and dual Ethernet ports
- Front panel LCD displays configuration, system status and audio levels
- Internal power supply
Symetrix 80-0204 Specifications:
- GENERAL SPECIFICATIONS:
- Processors: 1 x Analog Devices SHARC 21489 @ 400 MHz SIMD
- Raw processing capacity: 400 MIPS, 1.6 GFLOPS
- Sampling rate: 48 kHz, ± 100 ppm
- Frequency response (A/D/A): 20 Hz – 20 kHz, ± 0.5 dB
- Dynamic range (A/D/A): > 114 dB, A-weighted
- Channel separation (A/D/A): > 108 dB @ 1 kHz, +24 dBu
- Latency (A/D/A): 0.88 mS, inputs routed to outputs
- Delay memory: 174 mono seconds per Edge frame
- Analog control inputs: 0-3.3 VDC
- Recommended external control potentiometer: 10k Ohm, linear
- Logic outputs: Low (0V) when active, pulled high (5V) when inactive
- Logic output maximum external power supply voltage: 24 VDC
- Logic output maximum external power supply current sinking: 50 mA
- Logic output maximum output current: 10 mA
- RS-232 accessory serial I/O: 38.4 kbaud (default), 8 data bits, 1 stop bit, no parity, no flow control wired straight-through, only pins 2, 3, and 5 required.
- RS-485 serial I/O: 38.4 kbaud (default) 8 data bits, 1 stop bit, no parity, no flow control. May be broken out of ARC port.
- Ethernet cable: Standard CAT5, maximum device to device length = 100 meters
- Dante cable: Standard CAT6, maximum device to device length = 100 meters
- ARC cable: Standard CAT5, distance dependent upon load and number of devices
- Maximum devices per system: 32 units per Site File
- Maximum stored presets: 1000
- MECHANICAL SPECIFICATIONS:
- Space required: 1U (WDH: 18.91 in x 9.5 in x 1.72 in / 48.02 cm x 24.13 cm x 4.37 cm). Depth does not include connector allowance. Allow at least 3 inch additional clearance for rear panel connections. Additional depth may be required depending upon your specific wiring and connections.
- Electrical: 100-240 VAC, 50/60 Hz, 45 Watts maximum universal input and/or suitable 24 VDC / 2.0 Amp auxillary power source. No line voltage switching required.
- Ventilation: Maximum recommended ambient operating temperature is 30 C / 86 F. Ensure that the left and right equipment sides are unobstructed (5.08 cm, 2 in. minimum clearance).
- The ventilation should not be impeded by covering the ventilation openings with items such as newspapers, tablecloths, curtains, etc.
- Certifications or compliance: UL 60065, cUL 60065, IEC 60065, EN 55103-1, EN 55103-2, FCC Part 15, RoHS
- Shipping weight: 13 lbs. (5.9 kg) (CONFIRM)
