Meyer Sound ULTRA-X22 ULTRA-X22 3-Pin Install Speaker

The ULTRA-X22™ loudspeaker by Meyer Sound extends the advanced point source technology of the ULTRA-X40™ to a smaller, compact design. It offers high power output, low distortion, and consistent polar response in a vented enclosure. Featuring two 5-inch cone low-frequency drivers and a 2-inch diaphragm compression driver with a rotatable 80° x 50° constant-Q horn, the ULTRA-X22 delivers exceptional audio performance for size- and weight-critical applications.

Meyer Sound ULTRA-X22 Features:

• A compact, elegant and light aluminum enclosure encases exceptional fidelity and surprising power capability
• Extraordinarily flat amplitude and phase response ensures tonal accuracy and precise imaging
• Wide pattern covers broad listening areas
• Rotatable horn provides installation flexibility
• Integral stand mount and QuickFly® mounting options facilitate rigging

Meyer Sound ULTRA-X22 Specifications:

• Acoustical:
  • Operating Frequency Range: 60 Hz – 18 kHz
  • Frequency Response: 65 Hz – 17.5 kHz ± 4 dB
  • Phase Response: 95 Hz – 18 kHz ±45°
  • Linear Peak SPL: 128.5 dB with 20 dB crest factor (M-noise), 123.5 dB (Pink Noise), 125 dB (B-noise)
• Coverage:
  • Rotatable horn: 80° x 50°
  • Crossover: 830 Hz
• Transducers:
  • Low Frequency: Two 5-inch cone drivers; 6 Ω nominal impedance
  • High Frequency: One 2-inch diaphragm compression driver connected to a rotatable horn; 8 Ω nominal impedance
• Audio Input:
  • Analog Audion Version:
  • Type: Differential, electronically balanced
  • Maximum Common Mode Range: ±15 V DC, clamped to earth for voltage transient protection
  • Connectors: XLR 3-pin female input with male loop output.
  • Input Impedance: 10 kΩ differential between pins 2 and 3
• Wiring:
  • Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies
  • Pin 2: Signal +
  • Pin 3: Signal -
  • Case: Earth ground and chassis
  • Nominal Input Sensitivity: 0.0 dBV (1.0 V rms) continuous is typically the onset of limiting for noise and music
  • Input Level: Audio source must be capable of producing +20 dBV (10 V rms, 14 V peak) into 600 oms to produce the maximum peak SPL over the operating bandwidth of the loudspeaker
• Amplifier:
  • Type: Three-channel, Class-D
  • Total Output Power: 860 W peak
  • THD, IM, TIM: < 0.02%
  • Cooling: Convection
• AC Power:
  • Connectors: powerCON 20 input with loop output; powerCON TRUE1 TOP with loop output on digital and weather-protected units
  • Automatic Voltage Selection: 90–265 V AC, 50–60 Hz
  • Safety Rated Voltage Range: 100–240 V AC, 50–60 Hz
  • Turn-on and Turn-off Points: 90 V AC turn-on, no turn-off; internal fuse protection above 265 V AC
• Current Draw:
  • Idle Current: 0.15 A rms (115 V AC); 0.13 A rms (230 V AC); 0.16 A rms (100 V AC)
  • Maximum Long-Term Continuous Current (>10 sec): 0.9 A rms (115 V AC); 0.5 A rms (230 V AC); 1.1 A rms (100 V AC)
  • Burst Current (
  • Maximum Instantaneous Peak Current: 3.5 A peak (115 V AC); 1.8 A peak (230 V AC); 4.1 A peak (100 V AC)
  • Inrush Current: < 20 A peak
• Physical:
  • Dimensions: W: 7.44 in (189 mm) x H: 19.04 in (484 mm) x D: 8.66 in (220 mm)
  • Weight: 27 lb (12.3 kg)
  • Enclosure: Aluminum with slightly textured black finish
  • Two integrated M8 threaded points on each end; optional accessories for various rigging options (see accessories section); four M6 threaded holes with 5-inch by 2.75-inch (127 mm by 70 mm) hole pattern on the rear for use with third-party wall mounts.
  • Protective Grille: Powder-coated, round-perforated steel